Surface Preparation
The following steps are recommended for product performance.
All surfaces must be clean, dry and free of oil, grease, mildew, wax, dust, flaky rust, mill scale, loose paint, chalk and other foreign matter that could interfere with adhesion.
If washing is necessary, use a non-soapy detergent or a TSP substitute, rinse well and allow to dry.
Remove loose rust, peeling paint and mill scale with a scraper, wire brush or sandpaper.
Clean bare metal in accordance with SPC (The Society for Protective Coatings) specifications for the proper surface preparation of metal surfaces.
Peeling or Checked Paint: Scrape off loose paint and sand to a smooth surface. Sanding or removal of paint containing lead is hazardous.
Mold or Mildew Covered Surfaces: Wash the area with a mildew remover, rinse with water and allow to dry before priming.
While KILZ ADHESIONPrimer is formulated to bond without sanding, it is recommended that a small area be tested for adhesion prior to beginning the job.
Application
- Wear eye protection.
- Apply using a brush, roller or sprayer.
- Brush – High quality Nylon/Polyester
- Roller – High quality 3/8-1/2" nap on smooth surfaces or 1/2-3/4" nap on semi-rough or porous surfaces.
- Airless spray – .015-.021 tip / 60 mesh filter @ 2,500–3,200 PSI
- For spray applications, a small amount of water (no more than ½ pint per gallon) may be added.
- Only apply if surface, air and product temperatures are between 50°-90°F (10°-32°C).
- Stir thoroughly before and occasionally during use.
- Prime the entire surface to ensure a uniform appearance of the topcoat.
- Finishing: Topcoat within 30 days to prevent contamination of the primer before painting.
- Tinting: May be tinted with up to 2 oz. (60 mL) of universal colorant per gallon. Tinting to a lighter shade than the topcoat is recommended.
- Coverage: 300-400 sq. ft.(28-37 m2) per gallon depending on application method and surface porosity.
Dry Time @ 77°F (25°C), 50% RH
Dries to the touch in 30 minutes.
Recoat after 1 hour
Lower temperatures, higher humidity, poor ventilation or heavy application can significantly increase dry and recoat times.
Clean-Up & Disposal
- Clean equipment and paint spatters with warm, soapy water.
- Do not dispose of this product down a drain.
- Please consider donating any unused product.
- For recycling or disposal information contact your local household refuse collection service.
- If spilled, contain material and remove with an inert absorbent. Dispose of contaminated absorbent, container and unused product in accordance with all current local, state and federal regulations.
LIFETIME LIMITED WARRANTY
Masterchem Industries LLC warrants to you, the original residential consumer purchaser, the performance of this product as described on this label for so long as you reside in your home. If this product is found to be defective upon inspection by its representative, Masterchem Industries LLC will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty is not transferable. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. For warranty service, call: 1-866-774-6371, or email: techservice@masterchem.com. Masterchem Industries LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.
†Provided it is allowed to dry for 24 hours before topcoating and tested for compatibility in an inconspicuous area before full coat application.
†WARNING!
If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
WARNING
This product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
WARNING
Sanding or scraping pressure treated lumber may be hazardous; wear appropriate protection.
USE ONLY WITH ADEQUATE VENTILATION
Warning! Irritant!
HARMFUL OR FATAL IF SWALLOWED. CONTAINS ETHYLENE GLYCOL. Avoid contact with eyes. May cause eye, nose and throat irritation. Avoid breathing of dust, vapors or spray mist. Open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headache, or dizziness, or if air monitoring demonstrates vapor / mist levels are above applicable limits, wear an appropriate, properly fitted respirator (NIOSH / MSHA TC 23C or equivalent) during and after application. Follow respirator manufacturer’s direction for respirator use. Close container after each use. Wash thoroughly after handling and before smoking and eating.
First Aid
If swallowed, do not induce vomiting. Get medical attention immediately.
If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical attention immediately.
In case of eye contact, flush eyes immediately with plenty of water for at least 15 minutes and get medical attention.
KEEP FROM FREEZING.
KEEP OUT OF REACH OF CHILDREN
DO NOT TAKE INTERNALLY
Cautions / Limitations
IMPORTANT! DO NOT OPEN CAN WITHOUT READING INSTRUCTIONS
DO NOT USE ON FLOORS
DO NOT USE WHEN AIR AND SURFACE TEMPERATURES ARE BELOW 50ºF OR ABOVE 90ºF
SHELF LIFE UNDER NORMAL CONDITIONS IS TWO YEARS UNOPENED
Base
Water
Int/Ext
Int/Ext
Color
White
Coverage - Low
300 sq. ft.
Mils Wet
5.3
Mils Dry
2.2
Coverage High
400 sq. ft.
Mils Wet
4
Mils Dry
1.7
Finish @ 85°
< 10
Min Application Temp
50°F (10°C)
Max Application Temp
90°F (32°C)
Viscosity
93 - 100 KU
Dry To Touch
30 min
Dry To Recoat
1 hour
Max Tint
2 oz
VOC
100 g/L
Brush
Nylon / Poly
Roller - Smooth Surface
3/8" - 1/2" nap
Roller - Porous Surface
1/2" - 3/4" nap
Spray Tip
.015" - .021"
Spray Filter
60 mesh
Spray Pressure
2,500 - 3,200
Volume Solids
42% (+/-) 2%
Weight Solids
58% (+/-) 2%
Flashpoint
N/A
